109 lines
2.9 KiB
Plaintext
109 lines
2.9 KiB
Plaintext
0000:*** ERROR.eng = Error Text File for PRODAVE S7 ***
|
|
00CA:no resources available
|
|
00CB:configuration error
|
|
00CD:illegal call
|
|
00CE:module not found
|
|
00CF:driver not loaded
|
|
00D0:hardware fault
|
|
00D1:software fault
|
|
00D2:memory fault
|
|
00D7:no message
|
|
00D8:storage fault
|
|
00DB:internal timeout
|
|
00E1:too many channels open
|
|
00E2:internal fault
|
|
00E7:hardware fault
|
|
00E9:sin_serv.exe not started
|
|
00EA:protected
|
|
00F0:scp db file does not exist
|
|
00F1:no global dos storage available
|
|
00F2:error during transmission
|
|
00F2:error during reception
|
|
00F4:device does not exist
|
|
00F5:incorrect sub system
|
|
00F6:unknown code
|
|
00F7:buffer too small
|
|
00F8:buffer too small
|
|
00F9:incorrect protocol
|
|
00FB:reception error
|
|
00FC:licence error
|
|
0101:connection not established / parameterised
|
|
010A:negative acknowledgement received / timeout error
|
|
010C:data does not exist or disabled
|
|
012A:system storage no longer available
|
|
012E:incorrect parameter
|
|
0132:no memory in DPRAM
|
|
0201:incorrect interface specified
|
|
0202:maximum amount of interfaces exceeded
|
|
0203:PRODAVE already initialised
|
|
0204:wrong parameter list
|
|
0205:PRODAVE not initialised
|
|
0206:handle cannot be set
|
|
0207:data segment cannot be disabled
|
|
0300:initialisiation error
|
|
0301:initialisiation error
|
|
0302:block too small, DW does not exist
|
|
0303:block limit exceeded, correct amount
|
|
0310:no HW found
|
|
0311:HW defective
|
|
0312:incorrect config param
|
|
0313:incorrect baud rate / interrupt vect
|
|
0314:HSA parameterised incorrectly
|
|
0315:MPI address error
|
|
0316:HW device already allocated
|
|
0317:interrupt not available
|
|
0318:interrupt occupied
|
|
0319:sap not occupied
|
|
031A:no remote station found
|
|
031B:internal error
|
|
031C:system error
|
|
031D:error buffer size
|
|
0320:hardware fault
|
|
0321:DLL function error
|
|
0330:version conflict
|
|
0331:error com config
|
|
0332:hardware fault
|
|
0333:com not configured
|
|
0334:com not available
|
|
0335:serial drv in use
|
|
0336:no connection
|
|
0337:job rejected
|
|
0380:internal error
|
|
0381:hardware fault
|
|
0382:no driver or device found
|
|
0384:no driver or device found
|
|
03FF:system fault
|
|
0800:toolbox occupied
|
|
4001:connection not known
|
|
4002:connection not established
|
|
4003:connection is being established
|
|
4004:connection broken down
|
|
8000:function already actively occupied
|
|
8001:not allowed in this operating statu
|
|
8101:hardware fault
|
|
8103:object access not allowed
|
|
8104:context is not supported
|
|
8105:invalid address
|
|
8106:type (data type) not supported
|
|
8107:type (data type) not consistent
|
|
810A:object does not exist
|
|
8301:memory slot on CPU not sufficient
|
|
8404:grave error
|
|
8500:incorrect PDU size
|
|
8702:address invalid
|
|
D201:syntax error block name
|
|
D202:syntax error function parameter
|
|
D203:syntax error block type
|
|
D204:no linked block in storage medium
|
|
D205:object already exists
|
|
D206:object already exists
|
|
D207:block exists in EPROM
|
|
D209:block does not exist
|
|
D20E:no block available
|
|
D210:block number too big
|
|
D241:protection level of function not sufficie
|
|
D406:information not available
|
|
EF01:incorrect ID2
|
|
FFFB:TeleService Library not found
|
|
FFFE:unknown error FFFE hex
|
|
FFFF:timeout error. Check interface |